JDM Angler Supply is now open — authentic JDM tackle, shipped worldwide.

Pays / Langue

  • Worldwide Shipping

  • Extensive Product Selection

  • Authentic JDM Tackle

  • Expert Tackle Support

TENRYU Rod Model Numbers Explained

Decode TENRYU rod codes by series, length, sections, reel type, power, tip construction, and application suffixes.

TENRYU rod model number guide featuring an actual Rayz Integral RZI484S-UL multi-piece rod.

JWM611S-2/4 is a 6'1", one-piece spinning jigging rod. The final 1 in 611 is its section count. The 2/4 code means the rod combines a flexible class-2 tip with the stronger butt power of a class-4 rod. Separating section count from this tip-to-butt power pairing is the key to reading the model correctly.

TENRYU uses similar building blocks across its trout, shore, and offshore rods, with variations between product families. This guide follows the main patterns through specific models, separating information in the model name from the additional details in the specification table.

The Common Pattern: Series, Length, Sections, Reel Type, and Specification

Many models follow this sequence:

Series → length → section count → reel type → power and additional specification

For example, LK682S-MLT divides into:

Part Meaning
LK Lunakia
68 6 feet 8 inches
2 Two sections
S Spinning
ML Medium Light power
T Tubular tip

Read ML + T as Medium Light power plus a tubular tip.

S and B Identify Reel Type

In the models using this pattern, S means spinning and B means baitcasting, including offshore rods used with conventional reels. Rayz Integral offers a direct comparison: RZI484S-UL is spinning, while RZI484B-UL is casting. Both are 4'8", four-piece rods.

The position of the letter matters. In RZA622S-ULS, the first S identifies spinning tackle; the final S follows UL and identifies the solid tip. It is not a second reel-type designation.

Length and Section Count: Divide the Numeric Block Correctly

The length portion joins feet and inches. When a section-count digit follows, separate it before reading the length.

Model Numeric breakdown Assembled length Sections
JWM611S-2/4 61 + 1 6'1" 1
JWM5101B-5 510 + 1 5'10" 1
PM1022S-M 102 + 2 10'2" 2
SW1072S-ML 107 + 2 10'7" 2

These readings match the listed lengths and section counts. 510 divides into 5 feet and 10 inches; 102 divides into 10 feet and 2 inches. The position of the split is determined by the length format, not by a rule that always assigns the first two digits to feet.

Some Models Omit the Section-Count Digit

Horizon Progressive HPG66B-ML is a 6'6", one-piece casting model. Its numerical block is simply 66; the one-piece construction is stated in the specifications. The common pattern is useful, but the individual series still determines how much construction information appears in the name.

Official close view of a TENRYU Rayz Integral multi-piece rod joint and alignment marks.

Section count and closed length should be confirmed together; joint design determines how the rod packs. Source: Image: TENRYU

A Metric Pattern in ReAction-TENYA

RF2342S-MS uses a different numerical format: 234 corresponds to its 2.34 m overall length, followed by 2 for two sections. Similarly, RF2112B-MHT is listed at 2.11 m with two sections. These Red Flip ReAction-TENYA rods should not be read as feet-and-inches codes.

Recognize the Series Prefix

The prefix narrows the product family before you decode the rest of the name.

Prefix Product family
RZ Rayz
RZI Rayz Integral
RZS Rayz Spectra
RZA Rayz Alter
LK Lunakia
SW SWAT
PM / PMX Power Master / Power Master XTREAME
HMJ Horizon MJ
HPG Horizon Progressive
HLJ Horizon LJ
JWM Jig-ZAM Wild Mark
SK / SKX Spike / Spike XPG
RF Red Flip, including ReAction-TENYA models

The Rayz family distinguishes the main trout range from Integral's pack rods, Spectra, and the area-trout-oriented Alter series.

Among the shore and offshore families, Power Master addresses shore casting, the Horizon and Jig-ZAM ranges address jigging, and Spike addresses offshore casting. These are product-family identifiers, not a single ladder of rod power or component quality.

Power Labels: Standard Classes, Intermediate Settings, and Split Ratings

Power and Lure Rating Are Separate

Labels such as UL, L, ML, M, MH, and H identify Ultra Light, Light, Medium Light, Medium, Medium Heavy, and Heavy power classes. Use the listed lure or jig range to establish the intended working load of the particular model.

For example, RZ542S-L is a Light-power trout rod rated to 8 g, while HLJ632S-L is a Light-power jigging rod rated for 60–180 g jigs. The shared L does not give the two rods interchangeable working ranges.

LML: An Intermediate Power

TENRYU explicitly describes LK602S-LMLT as having power between L and ML. Read LML together, followed by T for the tubular tip. This intermediate rating should not automatically be rewritten as a Light tip joined to a Medium Light butt.

ML/M and ML/MH: Tip-to-Butt Power Distribution

For these SWAT casting models, TENRYU does specify different power at the tip and butt:

Model Tip-side power Butt-side power
SW842B-ML/M Medium Light Medium
SW932B-ML/MH Medium Light Medium Heavy

The split describes the rod's power distribution. It does not identify a joint position or a particular material connection.

1/3 and 2/4: The Jig-ZAM Wild Mark Approach

Wild Mark uses numerical split ratings. TENRYU explains 1/3 as a class-1 tip progressing to a class-3 butt; 2/4 follows the corresponding class-2-tip/class-4-butt arrangement. The concept combines a more accommodating tip for jig manipulation with a stronger lower section for fighting fish.

These are paired power classes, not fractions, section counts, or direct gram conversions. The model's jig rating remains a separate specification.

Tip Construction, Magna-Flex, and Action

Final S and T: Solid or Tubular Tip

In Rayz Alter, RZA622S-ULS has a solid tip, while RZA612S-LT has a tubular tip. Read S or T separately from the preceding power label.

The tip-type column supplies more detail than the final letter alone:

Tip-type notation Material or construction indicated
CT Carbon tubular
CS Carbon solid
MF/CT Magna-Flex carbon-tubular specification
MF/CS Magna-Flex construction combined with a carbon solid tip
MF/GT Magna-Flex glass-tubular specification
MF/GS Magna-Flex construction combined with a glass solid tip

CT and CS distinguish hollow carbon construction from a solid carbon tip. In the MF combinations, GT and GS distinguish glass tubular and glass solid. The Brigade Tobari lineup includes both: BT682B-L is listed as MF/GT, while BT652B-LS+ is MF/GS.

What Magna-Flex Adds

TENRYU describes two Magna-Flex approaches. Glass Flex combines glass and carbon—or glass materials with different characteristics—in a continuous tubular structure. Carbon Flex varies the carbon materials through the blank to create different bending characteristics at the tip, belly, and butt.

TENRYU official comparison of Glass Flex and Carbon Flex blank construction.

Glass Flex combines glass and carbon materials, while Carbon Flex varies carbon modulus through the blank to tune bending behavior. Source: Image: TENRYU

A Magna-Flex rod can also incorporate an attached solid tip. On RZA622S-ULS, TENRYU specifies a fine carbon solid tip fitted to a low-modulus Magna-Flex tubular section. Thus, MF/CS describes the combination; it does not mean the solid section was molded seamlessly with the entire blank.

Action Is Another Field

Action describes bending behavior rather than power or material. Among the specifications used here, F means Fast, RF means Regular Fast, R means Regular, and RS means Regular Slow. TENRYU lists action separately from the model code.

The distinction matters on Red Flip: RF642B-L/VDN is Regular Slow, whereas RF642B-M/VDK is Fast. Both use tubular blanks. Their different bite-handling approaches come from the complete design, not a simple solid-versus-tubular division.

Application Suffixes: P, VDN, VDK, and More

Power Master P: A Plugging-Specific Model

PM1002S-HP reads as Power Master, 10'0", two sections, spinning, Heavy power, and a plugging specification. TENRYU describes it specifically for shore plugging, with a more accommodating tip and a stronger lower section. Keep H and P separate: one is the power class, the other identifies the intended application.

Red Flip: Presentation and Hook-Setting Style

Red Flip combines boat presentation, depth, and hook-setting approach in its suffixes:

Suffix Manufacturer-described application
VDN Vertical, deep-water, NOSE (load-up style)
VDK Vertical, deep-water, KAKE (active hook-set style)
DN Dotera drift (boat drifting with wind and current), NOSE (load-up style)
DK Dotera drift (boat drifting with wind and current), KAKE (active hook-set style)
CN Casting, NOSE (load-up style)
CK Casting, KAKE (active hook-set style)
LN Longer-rod, NOSE (load-up style) model

Here, TENRYU’s NOSE label means a load-up style that lets the bite bend the rod during the retrieve; KAKE means an active style in which the angler initiates the hook-set. A dotera drift is a Japanese boat-fishing method in which the boat drifts with the wind and current, allowing the line to trail at an angle instead of keeping the presentation directly beneath the boat.

Read each suffix as a group: D refers to deep water in VDN/VDK, but to dotera in DN/DK. The corresponding weight ratings are also presentation-specific, so preserve labels such as Vertical, Dotera, and Cast when comparing specifications.

Four Complete Model Numbers, Decoded

Lunakia LK682S-MLT

LK / 68 / 2 / S / ML / T

Lunakia, 6'8", two sections, spinning, Medium Light, tubular tip. The 2026 model is listed at 2.03 m, with MF/CT construction, Regular action, a maximum 10 g lure rating, and a 104 cm closed length. Its stated role covers plugs and several light-rig presentations.

Rayz Integral RZI484S-UL

RZI / 48 / 4 / S / UL

Rayz Integral, 4'8", four sections, spinning, Ultra Light. TENRYU lists 1.42 m overall length, a 39 cm closed length, Regular action, and a maximum 6 g lure rating. The manufacturer describes it for small plugs, spoons, and spinners, with compact casting motions in stream-trout settings.

[[JDMAS:tenryu-rzi484s-ul]]

Jig-ZAM Wild Mark JWM611S-2/4

JWM / 61 / 1 / S / 2/4

Jig-ZAM Wild Mark, 6'1", one-piece, spinning, class-2 tip/class-4 butt. Its specification table lists 1.86 m overall length, Regular Fast action, a 130–250 g jig range with 220 g marked “Best,” and maximum PE #4. The 2/4 pairing describes power distribution; the jig range is listed separately.

[[JDMAS:tenryu-jwm611s-2-4]]

Red Flip RF642B-M/VDK

RF / 64 / 2 / B / M / VDK

Red Flip, 6'4", two sections, baitcasting/conventional, Medium, Vertical Deep KAKE (active hook-set) specification. It has a grip joint and a 144 cm closed length. TENRYU lists Fast action, 60–180 g for vertical tai-rubber fishing—a boat technique using a skirted sliding-head lure for red sea bream—and a separate dotera maximum of 250 g. The vertical rating is not a casting rating.

[[JDMAS:tenryu-rf642b-m-vdk]]

Finish the Comparison with the Specification Table

A section count tells you how many parts the rod has, not where those parts join. Spike XPG SKX832S-H is an 8'3" two-piece rod, but its removable-grip construction leaves a 177 cm closed length. Compare the actual packed dimension when planning transport.

Weight ratings also need their labels. On Horizon Progressive HPG66B-ML, TENRYU lists a 150 g maximum jig weight and 100 g as “Best.” Those are different pieces of guidance. Do not replace a preferred working weight with the upper limit, or treat an offshore jig rating as a casting specification.

For the final choice, read the complete model code, then compare the intended presentation, lure or jig range, line rating, action, joint arrangement, and closed length. Listed rear-grip dimensions can help compare handle layouts, but they remain separate from both fishing length and packed length.

[[JDMAS:tenryu-brand-collection]]

Key references